Land Bayern

This page provides supplementary data to the article properties of water.

Further comprehensive authoritative data can be found at the NIST Chemistry WebBook page on thermophysical properties of fluids.^[1]

Vapor pressure formula for steam in equilibrium with liquid water:^[14]

where P is equilibrium vapor pressure in kPa, and T is temperature in kelvins.

For T = 273 K to 333 K: A = 7.2326; B = 1750.286; C = 38.1.

For T = 333 K to 423 K: A = 7.0917; B = 1668.21; C = 45.1.

Data in the table above is given for water–steam equilibria at various temperatures over the entire temperature range at which liquid water can exist. Pressure of the equilibrium is given in the second column in kPa. The third column is the heat content of each gram of the liquid phase relative to water at 0 °C. The fourth column is the heat of vaporization of each gram of liquid that changes to vapor. The fifth column is the work PΔV done by each gram of liquid that changes to vapor. The sixth column is the density of the vapor.

Data obtained from CRC Handbook of Chemistry and Physics 44th ed., p. 2390.

^‡Ice XI triple point is theoretical and has never been obtained

Note: ρ is density, n is refractive index at 589 nm,^{[clarification needed]} and η is viscosity, all at 20 °C; T_eq is the equilibrium temperature between two phases: ice/liquid solution for T_eq < 0–0.1 °C and NaCl/liquid solution for T_eq above 0.1 °C.

The data that follows was copied and translated from the German language Wikipedia version of this page (which has moved to here). It provides supplementary physical, thermodynamic, and vapor pressure data, some of which is redundant with data in the tables above, and some of which is additional.

In the following tables, values are temperature-dependent and to a lesser degree pressure-dependent, and are arranged by state of aggregation (s = solid, lq = liquid, g = gas), which are clearly a function of temperature and pressure. All of the data were computed from data given in "Formulation of the Thermodynamic Properties of Ordinary Water Substance for Scientific and General Use" (IAPWS , 1984) (obsolete as of 1995).^[22] This applies to:

• T – temperature in degrees Celsius
• V – specific volume in cubic decimeters per kilogram (1 dm³ is equivalent to 1 liter)
• H – specific enthalpy in kilojoules per kilogram
• U – specific internal energy in kilojoules per kilogram
• S – specific entropy in kilojoules per kilogram-kelvin
• c_p – specific heat capacity at constant pressure in kilojoules per kilogram-kelvin
• γ – Thermal expansion coefficient as 10⁻³ per kelvin
• λ – Heat conductivity in milliwatts per meter-kelvin
• η – Viscosity in micropascal-seconds (1 cP = 1000 μPa·s)
• σ – surface tension in millinewtons per meter (equivalent to dyn/cm)

In the following table, material data are given for standard pressure of 0.1 MPa (equivalent to 1 bar). Up to 99.63 °C (the boiling point of water at 0.1 MPa), at this pressure water exists as a liquid. Above that, it exists as water vapor. Note that the boiling point of 100.0 °C is at a pressure of 0.101325 MPa (1 atm), which is the average atmospheric pressure.

In the following table, material data are given with a pressure of 611.7 Pa (equivalent to 0.006117 bar). Up to a temperature of 0.01 °C, the triple point of water, water normally exists as ice, except for supercooled water, for which one data point is tabulated here. At the triple point, ice can exist together with both liquid water and vapor. At higher temperatures, the data are for water vapor only.

The following table is based on different, complementary sources and approximation formulas, whose values are of various quality and accuracy. The values in the temperature range of −100 °C to 100 °C were inferred from D. Sunday (1982) and are quite uniform and exact. The values in the temperature range of the boiling point of water up to the critical point (100 °C to 374 °C) are drawn from different sources and are substantially less accurate; hence they should be used only as approximate values.^{[23][24][25][26]}

To use the values correctly, consider the following points:

• The values apply only to smooth interfaces and in the absence other gases or gas mixtures such as air. Hence they apply only to pure phases and need a correction factor for systems in which air is present.
• The values were not computed according formulas widely used in the US, but using somewhat more exact formulas (see below), which can also be used to compute further values in the appropriate temperature ranges.
• The saturated vapor pressure over water in the temperature range of −100 °C to −50 °C is only extrapolated [Translator's note: Supercooled liquid water is not known to exist below −42 °C].
• The values have various units (Pa, hPa or bar), which must be considered when reading them.

The table values for −100 °C to 100 °C were computed by the following formulas, where T is in kelvins and vapor pressures, P_w and P_i, are in pascals.

Over liquid water

log_e(P_w) = −6094.4642 T⁻¹ + 21.1249952 − 2.724552×10⁻² T + 1.6853396×10⁻⁵ T² + 2.4575506 log_e(T)

For temperature range: 173.15 K to 373.15 K or equivalently −100 °C to 100 °C

Over ice

log_e(P_i) = −5504.4088 T⁻¹ − 3.5704628 − 1.7337458×10⁻² T + 6.5204209×10⁻⁶ T² + 6.1295027 log_e(T)

For temperature range: 173.15 K to 273.15 K or equivalently −100 °C to 0 °C

At triple point

An important basic value, which is not registered in the table, is the saturated vapor pressure at the triple point of water. The internationally accepted value according to measurements of Guildner, Johnson and Jones (1976) amounts to:

P_w(t_tp = 0.01 °C) = 611.657 Pa ± 0.010 Pa at (1 − α) = 99%

Accepted standardized value of the magnetic susceptibility of water at 20 °C (room temperature) is −12.97 cm³/mol.^[27]

Accepted standardized value of the magnetic susceptibility of water at 20 °C (room temperature) is −0.702 cm³/g.^[27]

• Properties of water

• Microwave Spectrum (by NIST)
• Water properties by Martin Chaplin, London South Bank University.